Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
What're your thoughts concerning How to Install a Bathtub Yourself?
Setting up a bathtub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately difficult project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have currently purchased a new tub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and product checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow electrical outlet and the typical outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Planning for the Installation
First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split an inflexible seal, causing the water to permeate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the market. It is advisable to fit the tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry on Installing A Bathtub when looking around the web. Are you aware of another individual who is interested by A Step-by-Step Guide to Installing a Bathtub? Feel free to promote it. Thank you so much for taking the time to read it.
Book Inspection
Report this page